//------------------------------------------- Mycpu.v 文件的開始  ------------------------------------------- /****************************************************************************** `timescale 1ns/1ns module CPU(input             clk,                //時鐘            input             reset_n,            //復位信號            inout      [15:0] rddata,             //讀數據            output reg        rd,                 //讀使能            output reg        halt,               //停機指示            output reg [12:0] addr               //地址            );                      //CPU內部用寄存器          reg [1:0]  state;                       //狀態          reg [12:0] ip;                          //指令指針.           reg [15:0]  opcode;                       //操作碼          reg [15:0] opx1;                       //x1          reg [15:0] opy1;                       //y1          reg [15:0] opx2;                        //x2          reg [15:0] opy2;                        //y2 parameter HLT="HT", G0="G0", G1="G1";          parameter S0=3'b000, S1=3'b001, S2=3'b010;S3=3'b011;S4=3'b100;S5=3'b101;S6=3'b110; //s0指令處理,S1:計算,s2準備讀指令S3讀寫數據X1,S4讀寫數據Y1,S5讀寫數據X2,S6讀寫數據Y2, always@(posedge clk or negedge reset_n)    if(!reset_n)                                  //如果復位有效         begin         rd<=1'b1;                                //讀信號無效          halt<=1'b0;                              //清停機指示         addr<=13'b0;                             //初始指令地址為0         ip<=13'b0;                               //指令指針清0，從0地址執行程序         state<=S2;                               //下一狀態為讀指令周期         end     else             case(state)             S0:                                       begin                        //讀指令處理                        state<=S1;              //設置下一狀態                 opy2<=rddata;                                                   case(opcode)      //根據操作碼不同進行處理                                 HLT:             //停機                                     begin                                     rd<=1'b1;                                       halt<=1'b1;    //置停機標志                                     end                                     G0:             //G0                                      begin                                              rd<=1'b1;                                         ip<=ip+3'd5;   //指令指針加5                                                                             end                                     G1:           //G1                                     begin                                                                           rd<=1'b1;                                                     ip<=ip+12'd5;        //指令指針加5                                           end                                                                                 endcase                          end           S1:                                                  //計算周期                           begin                 rd<=1'b1;                                    //下一狀態讀無效                 state<=S2;                                               case(opcode)                         G0:                                 //執行G0                         //執行G0                         G1:                                //執行G1                         //執行G1;                        endcase                 end             S2:                                                  //準備讀指令                begin                      state<=S3;                 rd<=1'b0;                                    //設置度信號                 addr<=ip;                                    //指令地址                                  end         S3:                                                  //讀寫數據周期               begin                      state<=S4;                 opcode<=rddata;                         rd<=1'b0;                                    //設置度信號                  addr<=addr+3'd1;                                    //x1                                          end         S4:                                                  //讀寫數據周期                begin                      state<=S5;                 opx1=rddata;                         rd<=1'b0;                   addr<=addr+3'd1;                                //y1                      end         S5:                                                  //讀寫數據周期                begin                      state<=S6;                 opy1=rddata;                                           rd<=1'b0;                   addr<=addr+3'd1;                             //x2                             end         S6:                                                  //讀寫數據周期                  begin                      state<=S0;                 opx2=rddata;                           rd<=1'b0;                                    //設置度信號                 addr<=addr+3'd1;                                 //y2             end                  endcase endmodule 代碼形式為:G1X1Y1X2Y2為連續從外部RAM讀入5個字,第一個字是操作碼,第二個字是X1,第二個字是Y1,第二個字是X2,第二個字是Y2. //它們之間是不是需要延時?,是不是用阻塞賦值? //這段程序經過高手確定沒問題以后,才能繼續了. //呵呵,需要安裝CPLD模擬環境了,我還不會,現學.:) //請高手指教，歡迎拍磚

`用ST32單片機控制的DIY雕刻機`

學長留下了個diy雕刻機，主控是arduino uno。驅動軟件Grbl Controller，文件是nc格式的，想請教如何將pcb轉化成nc？

`一款為了滿足個人玩家、數控教育、以及低成本設計制造，而生產的桌面型五軸雕刻機。整機僅重20kg可以任意放置在桌面上操作使用，在低運營成本的情況下快速完成設計到加成品的過程。`

``請幫幫我，看別人diy雕刻機，腦袋一熱也想做臺，買了30a 12v直流電機調速器，220v轉24v 15a 300w電源，799電機12-24v,四臺42步進電機2a 4線的,一套arduino

DIY自制激光雕刻機教程

我原來在16年初的時候，用光驅的步進電機DIY了1個簡易的雕刻機，有人提到用雕刻機做PCB板，但光驅步進電機功率太小，所以重新設計了這個雕刻機。主要分成2部分，一部分為控制器，一部分為

原標題：雕刻機限位怎么解決數控木工雕刻機越來越得到客戶的青睞，在一定程度上提高了生產質量和生產效率，但由于木工雕刻機屬于新時代產物，很多客戶都是使用木工雕刻機的新手，很多都只是能簡單的

七百塊DIY一臺自己的雕刻機三軸的雕刻機我想對于理工科的學生來說都不陌生，這東西對于喜歡DIY一些東西的人來說絕對是必不可少的機器。但是雕刻機