Cypress公司的EZ-PD? CCG2是USB Type-C型控制器，它符合最新USB Type-C 型和PD 標準。EZ-PD CCG2 為無源線纜，主動線纜和電源配件提供了一個完整的USB Type-C 和USB 供電端口控制解決方案.EZ-PDCCG2 使用賽普拉斯的專用M0S8 技術，該技術使用了帶有32 KB 閃存的32 位48 MHz ARM? Cortex?-M0 處理器；該處理器集成了一個包括RP、RD 和RAType-C 型電阻的完整的Type-C 型收發器。主要用在 USB Type-C 型的EMCA 線纜， 供電配件， 上行方向端口以及下行方向端口。本文介紹了EZ-PD? CCG2主要特性，邏輯框圖，功能框圖以及USB-PD子系統框圖，CCG2 60W汽車充電器參考設計文件，電路圖和材料清單。

EZ-PD? CCG2 is a USB Type-C controller that complies with the latest USB Type-C and PD standards. EZ-PD CCG2 provides acomplete USB Type-C and USB Power Delivery port control solution for passive cables， active cables， and powered accessories. Itcan also be used in many upstream and downstream facing port applications.EZ-PD CCG2 uses Cypress’s proprietary M0S8technology with a 32-bit， 48-MHz ARM? Cortex?-M0 processor with 32-KB flash and integrates a complete Type-C Transceiverincluding the Type-C termination resistors RP， RD and RA.

EZ-PD? CCG2主要特性：

32-bit MCU Subsystem

■ 48-MHz ARM Cortex-M0 CPU

■ 32-KB Flash

■ 4-KB SRAM

■ In-system reprogrammable

Integrated Digital Blocks

■ Integrated timers and counters to meet response timesrequired by the USB-PD protocol

■ Run-time reconfigurable serial communication block （SCB）with reconfigurable I2C， SPI， or UART functionality

Clocks and Oscillators

■ Integrated oscillator eliminating the need for external clock

Type-C Support

■ Integrated transceiver （baseband PHY）

■ Integrated UFP （RD）， EMCA （RA） termination resistors， andcurrent sources for DFP （RP）

■ Supports one USB Type-C port

Low-Power Operation

■ 2.7-V to 5.5-V operation

■ Two independent VCONN rails with integrated isolationbetween the two

■ Independent supply voltage pin for GPIO that allows 1.71-V to5.5-V signaling on the I/Os

■ Reset： 1.0 μA， Deep Sleep： 2.5 μA， Sleep： 2.0 mA

System-Level ESD on CC and VCONN Pins

■ ± 8-kV Contact Discharge and ±15-kV Air Gap Discharge basedon IEC61000-4-2 level 4C

Packages

■ 1.63 mm × 2.03 mm， 20-ball wafer-level CSP （WLCSP） with0.4-mm ball pitch

■ 2.5 mm × 3.5 mm × 0.6 mm 14-pin DFN

■ 4.0 mm × 4.0 mm， 0.55 mm 24-pin QFN

■ Supports industrial （40℃ to +85℃） and extended industrial（40℃ to +105℃） temperature ranges

EZ-PD? CCG2應用：

■ USB Type-C EMCA cables

■ USB Type-C powered accessories

■ USB Type-C upstream facing ports

■ USB Type-C downstream facing ports

圖1.EZ-PD? CCG2邏輯框圖

圖2. EZ-PD? CCG2框圖

圖3. EZ-PD? CCG2 USB-PD子系統框圖

CCG2 60W汽車充電器參考設計

The CCG2 60W Car Charger Reference Design Board is a receptacle based USB-C Charger with USB PD 2.0 and QC 3.0 (Class –A and Class –B) support. In the PD mode, it?supports 5V@3A, 7V@3A, 8V@3A, 9V@3A, 12V@3A, 15V@3A and 20V@3A output. ?The board can be programmed to support any output voltage between 0 to 20V with 100mV resolution. It is designed to work with standard Car Lighter Attachment (CLA). It works with any DC input between 4V to 24V.

The two major components on the board are Cypress’s EZ-PD CCG2?(CYPD2134-24LQXIT) controller and On Semiconductor’s NCP81239 DC-DC Buck-Boost controller.?

圖4.CCG2 60W汽車充電器參考設計外形圖

The CCG2 device handles USB Type-C interface, Power Delivery (PD) 2.0, QC 3.0, Cable compensation and primary Over Current Protection (OCP). The buck-boost conversion, Over Current Protection (OCP) and Over Voltage Protection (OVP) are?handled by On Semiconductor’s NCP81239 DC-DC Buck-Boost controller. The board hardware design files (schematic, bill of materials, layout etc) are readily available below for customers to reduce the design cycle.

圖5. CCG2 60W汽車充電器參考設計電路圖(1)

圖6. CCG2 60W汽車充電器參考設計電路圖(2)

圖7. CCG2 60W汽車充電器參考設計電路圖(3)

CCG2 60W汽車充電器參考設計材料清單:

CCG2 60W汽車充電器參考設計文件見: